fence_brocade(8)

fence_brocade - Fence agent for HP Brocade over telnet/ssh

Section 8 fence-agents bookworm source

Description

FENCE_AGENT

NAME

fence_brocade - Fence agent for HP Brocade over telnet/ssh

DESCRIPTION

fence_brocade is an I/O Fencing agent which can be used with Brocade FC switches. It logs into a Brocade switch via telnet and disables a specified port. Disabling the port which a machine is connected to effectively fences that machine. Lengthy telnet connections to the switch should be avoided while a GFS cluster is running because the connection will block any necessary fencing actions. After a fence operation has taken place the fenced machine can no longer connect to the Brocade FC switch. When the fenced machine is ready to be brought back into the GFS cluster (after reboot) the port on the Brocade FC switch needs to be enabled. This can be done by running fence_brocade and specifying the enable action

fence_brocade accepts options on the command line as well as from stdin. Fenced sends parameters through stdin when it execs the agent. fence_brocade can be run by itself with command line options. This is useful for testing and for turning outlets on or off from scripts.

Vendor URL: http://www.brocade.com

PARAMETERS

-o, --action=[action]

Fencing action (Default Value: off)

-c, --command-prompt=[prompt]

Force Python regex for command prompt (Default Value: [’> ’])

-k, --identity-file=[filename]

Identity file (private key) for SSH

-4, --inet4-only

Forces agent to use IPv4 addresses only

-6, --inet6-only

Forces agent to use IPv6 addresses only

-a, --ip=[ip]

IP address or hostname of fencing device This parameter is always required.

-u, --ipport=[port]

TCP/UDP port to use for connection with device (Default Value: 23)

-p, --password=[password]

-S, --password-script=[script]

Script to run to retrieve password

-n, --plug=[id]

Physical plug number on device, UUID or identification of machine This parameter is always required.

-x, --ssh

Use SSH connection

--ssh-options=[options]

SSH options to use

-l, --username=[name]

-q, --quiet

Disable logging to stderr. Does not affect --verbose or --debug-file or logging to syslog.

-v, --verbose

Verbose mode. Multiple -v flags can be stacked on the command line (e.g., -vvv) to increase verbosity.

--verbose-level

Level of debugging detail in output. Defaults to the number of --verbose flags specified on the command line, or to 1 if verbose=1 in a stonith device configuration (i.e., on stdin).

-D, --debug-file=[debugfile]

Write debug information to given file

-V, --version

Display version information and exit

-h, --help

Display help and exit

--plug-separator=[char]

Separator for plug parameter when specifying more than 1 plug (Default Value: ,)

-C, --separator=[char]

Separator for CSV created by ’list’ operation (Default Value: ,)

--delay=[seconds]

Wait X seconds before fencing is started (Default Value: 0)

--disable-timeout=[true/false]

Disable timeout (true/false) (default: true when run from Pacemaker 2.0+)

--login-timeout=[seconds]

Wait X seconds for cmd prompt after login (Default Value: 5)

--power-timeout=[seconds]

Test X seconds for status change after ON/OFF (Default Value: 20)

--power-wait=[seconds]

Wait X seconds after issuing ON/OFF (Default Value: 0)

--shell-timeout=[seconds]

Wait X seconds for cmd prompt after issuing command (Default Value: 3)

--stonith-status-sleep=[seconds]

Sleep X seconds between status calls during a STONITH action (Default Value: 1)

--retry-on=[attempts]

Count of attempts to retry power on (Default Value: 1)

--ssh-path=[path]

Path to ssh binary (Default Value: /usr/bin/ssh)

--telnet-path=[path]

Path to telnet binary (Default Value: /usr/bin/telnet)

ACTIONS

	on		Power on machine.
	off		Power off machine.

status

This returns the status of the plug/virtual machine.

list

List available plugs with aliases/virtual machines if there is support for more then one device. Returns N/A otherwise.

list-status

List available plugs with aliases/virtual machines and their power state if it can be obtained without additional commands.

monitor

Check the health of fence device

metadata

Display the XML metadata describing this resource.

manpage

The operational behavior of this is not known.

validate-all

Validate if all required parameters are entered.

STDIN PARAMETERS

action

Fencing action (Default Value: off)

command_prompt

Force Python regex for command prompt (Default Value: [’> ’]) Obsoletes: cmd_prompt

identity_file

Identity file (private key) for SSH

inet4_only

Forces agent to use IPv4 addresses only

inet6_only

Forces agent to use IPv6 addresses only

IP address or hostname of fencing device This parameter is always required. Obsoletes: ipaddr

ipport

TCP/UDP port to use for connection with device (Default Value: 23)

password

password_script

Script to run to retrieve password Obsoletes: passwd_script

	plug		Physical plug number on device, UUID or identification of machine This parameter is always required. Obsoletes: port
	ssh		Use SSH connection Obsoletes: secure

ssh_options

SSH options to use

username

quiet

Disable logging to stderr. Does not affect --verbose or --debug-file or logging to syslog.

verbose

Verbose mode. Multiple -v flags can be stacked on the command line (e.g., -vvv) to increase verbosity.

verbose_level

Level of debugging detail in output. Defaults to the number of --verbose flags specified on the command line, or to 1 if verbose=1 in a stonith device configuration (i.e., on stdin).

debug_file

Write debug information to given file Obsoletes: debug

version

Display version information and exit

help

Display help and exit

plug_separator

Separator for plug parameter when specifying more than 1 plug (Default Value: ,)

separator

Separator for CSV created by ’list’ operation (Default Value: ,)

delay

Wait X seconds before fencing is started (Default Value: 0)

disable_timeout

Disable timeout (true/false) (default: true when run from Pacemaker 2.0+)

login_timeout

Wait X seconds for cmd prompt after login (Default Value: 5)

power_timeout

Test X seconds for status change after ON/OFF (Default Value: 20)

power_wait

Wait X seconds after issuing ON/OFF (Default Value: 0)

shell_timeout

Wait X seconds for cmd prompt after issuing command (Default Value: 3)

stonith_status_sleep

Sleep X seconds between status calls during a STONITH action (Default Value: 1)

retry_on

Count of attempts to retry power on (Default Value: 1)

ssh_path

Path to ssh binary (Default Value: /usr/bin/ssh)

telnet_path

Path to telnet binary (Default Value: /usr/bin/telnet)