fence_intelmodular(8)

fence_intelmodular - Fence agent for Intel Modular

Section 8 fence-agents bookworm source

Description

FENCE_AGENT

NAME

fence_intelmodular - Fence agent for Intel Modular

DESCRIPTION

fence_intelmodular is an I/O Fencing agent which can be used with Intel Modular device (tested on Intel MFSYS25, should work with MFSYS35 as well).

Note: Since firmware update version 2.7, SNMP v2 write support is removed, and replaced by SNMP v3 support. So agent now has default SNMP version 3. If you are using older firmware, please supply -d for command line and snmp_version option for your cluster.conf.

fence_intelmodular accepts options on the command line as well as from stdin. Fenced sends parameters through stdin when it execs the agent. fence_intelmodular can be run by itself with command line options. This is useful for testing and for turning outlets on or off from scripts.

Vendor URL: http://www.intel.com

PARAMETERS

-o, --action=[action]

Fencing action (Default Value: reboot)

-c, --community=[community]

Set the community string

-a, --ip=[ip]

IP address or hostname of fencing device This parameter is always required.

-u, --ipport=[port]

TCP/UDP port to use for connection with device (Default Value: 161)

-p, --password=[password]

Login password or passphrase

-S, --password-script=[script]

Script to run to retrieve password

-n, --plug=[id]

Physical plug number on device, UUID or identification of machine This parameter is always required.

-b, --snmp-auth-prot=[prot]

Set authentication protocol (MD5|SHA)

-P, --snmp-priv-passwd=[pass]

Set privacy protocol password

-R, --snmp-priv-passwd-script

Script to run to retrieve privacy password

-B, --snmp-priv-prot=[prot]

Set privacy protocol (DES|AES)

-E, --snmp-sec-level=[level]

Set security level (noAuthNoPriv|authNoPriv|authPriv)

-d, --snmp-version=[version]

Specifies SNMP version to use (1|2c|3)

-l, --username=[name]

Login name

-q, --quiet

Disable logging to stderr. Does not affect --verbose or --debug-file or logging to syslog.

-v, --verbose

Verbose mode. Multiple -v flags can be stacked on the command line (e.g., -vvv) to increase verbosity.

--verbose-level

Level of debugging detail in output. Defaults to the number of --verbose flags specified on the command line, or to 1 if verbose=1 in a stonith device configuration (i.e., on stdin).

-D, --debug-file=[debugfile]

Write debug information to given file

-V, --version

Display version information and exit

-h, --help

Display help and exit

--plug-separator=[char]

Separator for plug parameter when specifying more than 1 plug (Default Value: ,)

-C, --separator=[char]

Separator for CSV created by ’list’ operation (Default Value: ,)

--delay=[seconds]

Wait X seconds before fencing is started (Default Value: 0)

--disable-timeout=[true/false]

Disable timeout (true/false) (default: true when run from Pacemaker 2.0+)

--login-timeout=[seconds]

Wait X seconds for cmd prompt after login (Default Value: 5)

--power-timeout=[seconds]

Test X seconds for status change after ON/OFF (Default Value: 20)

--power-wait=[seconds]

Wait X seconds after issuing ON/OFF (Default Value: 0)

--shell-timeout=[seconds]

Wait X seconds for cmd prompt after issuing command (Default Value: 3)

--stonith-status-sleep=[seconds]

Sleep X seconds between status calls during a STONITH action (Default Value: 1)

--retry-on=[attempts]

Count of attempts to retry power on (Default Value: 1)

--snmpget-path=[path]

Path to snmpget binary (Default Value: /usr/bin/snmpget)

--snmpset-path=[path]

Path to snmpset binary (Default Value: /usr/bin/snmpset)

--snmpwalk-path=[path]

Path to snmpwalk binary (Default Value: /usr/bin/snmpwalk)

ACTIONS

on

Power on machine.

off

Power off machine.

reboot

Reboot machine.

status

This returns the status of the plug/virtual machine.

list

List available plugs with aliases/virtual machines if there is support for more then one device. Returns N/A otherwise.

list-status

List available plugs with aliases/virtual machines and their power state if it can be obtained without additional commands.

monitor

Check the health of fence device

metadata

Display the XML metadata describing this resource.

manpage

The operational behavior of this is not known.

validate-all

Validate if all required parameters are entered.

STDIN PARAMETERS

action

Fencing action (Default Value: reboot)

community

Set the community string

ip

IP address or hostname of fencing device This parameter is always required. Obsoletes: ipaddr

ipport

TCP/UDP port to use for connection with device (Default Value: 161)

password

Login password or passphrase Obsoletes: passwd

password_script

Script to run to retrieve password Obsoletes: passwd_script

plug

Physical plug number on device, UUID or identification of machine This parameter is always required. Obsoletes: port

snmp_auth_prot

Set authentication protocol (MD5|SHA)

snmp_priv_passwd

Set privacy protocol password

snmp_priv_passwd_script

Script to run to retrieve privacy password

snmp_priv_prot

Set privacy protocol (DES|AES)

snmp_sec_level

Set security level (noAuthNoPriv|authNoPriv|authPriv)

snmp_version

Specifies SNMP version to use (1|2c|3)

username

Login name Obsoletes: login

quiet

Disable logging to stderr. Does not affect --verbose or --debug-file or logging to syslog.

verbose

Verbose mode. Multiple -v flags can be stacked on the command line (e.g., -vvv) to increase verbosity.

verbose_level

Level of debugging detail in output. Defaults to the number of --verbose flags specified on the command line, or to 1 if verbose=1 in a stonith device configuration (i.e., on stdin).

debug_file

Write debug information to given file Obsoletes: debug

version

Display version information and exit

help

Display help and exit

plug_separator

Separator for plug parameter when specifying more than 1 plug (Default Value: ,)

separator

Separator for CSV created by ’list’ operation (Default Value: ,)

delay

Wait X seconds before fencing is started (Default Value: 0)

disable_timeout

Disable timeout (true/false) (default: true when run from Pacemaker 2.0+)

login_timeout

Wait X seconds for cmd prompt after login (Default Value: 5)

power_timeout

Test X seconds for status change after ON/OFF (Default Value: 20)

power_wait

Wait X seconds after issuing ON/OFF (Default Value: 0)

shell_timeout

Wait X seconds for cmd prompt after issuing command (Default Value: 3)

stonith_status_sleep

Sleep X seconds between status calls during a STONITH action (Default Value: 1)

retry_on

Count of attempts to retry power on (Default Value: 1)

snmpget_path

Path to snmpget binary (Default Value: /usr/bin/snmpget)

snmpset_path

Path to snmpset binary (Default Value: /usr/bin/snmpset)

snmpwalk_path

Path to snmpwalk binary (Default Value: /usr/bin/snmpwalk)