Sg3-Utils

• rescan-scsi-bus.sh(8) script to add and remove SCSI devices without rebooting
• scsi_logging_level(8) access Linux SCSI logging level information
• scsi_mandat(8) check SCSI device support for mandatory commands
• scsi_readcap(8) do SCSI READ CAPACITY command on disks
• scsi_ready(8) do SCSI TEST UNIT READY on devices
• scsi_satl(8) check SCSI to ATA Translation (SAT) device support
• scsi_start(8) start one or more SCSI disks
• scsi_stop(8) stop (spin down) one or more SCSI disks
• scsi_temperature(8) fetch the temperature of a SCSI device
• sg_bg_ctl(8) send SCSI BACKGROUND CONTROL command
• sg_compare_and_write(8) send the SCSI COMPARE AND WRITE command
• sg_copy_results(8) send SCSI RECEIVE COPY RESULTS command (XCOPY related)
• sg_dd(8) copy data to and from files and devices, especially SCSI
• sg_decode_sense(8) decode SCSI sense and related data
• sg_emc_trespass(8) change ownership of SCSI LUN from another
• sg_format(8) format, format with preset, resize SCSI disk; format tape
• sg_get_config(8) send SCSI GET CONFIGURATION command (MMC-4 +)
• sg_get_elem_status(8) send SCSI GET PHYSICAL ELEMENT STATUS command
• sg_get_lba_status(8) send SCSI GET LBA STATUS(16 or 32) command
• sg_ident(8) send SCSI REPORT/SET IDENTIFYING INFORMATION command
• sg_inq(8) issue SCSI INQUIRY command and/or decode its response
• sg_logs(8) access log pages with SCSI LOG SENSE command
• sg_luns(8) send SCSI REPORT LUNS command or decode given LUN
• sg_map(8) displays mapping between Linux sg and other SCSI devices
• sg_map26(8) map SCSI generic (sg) device to corresponding device names
• sg_modes(8) reads mode pages with SCSI MODE SENSE command
• sg_opcodes(8) report supported SCSI commands or task management functions
• sg_persist(8) use SCSI PERSISTENT RESERVE command to access registrations
• sg_prevent(8) send SCSI PREVENT ALLOW MEDIUM REMOVAL command
• sg_raw(8) send arbitrary SCSI or NVMe command to a device
• sg_rbuf(8) reads data using SCSI READ BUFFER command
• sg_rdac(8) display or modify SCSI RDAC Redundant Controller mode page
• sg_read_attr(8) send SCSI READ ATTRIBUTE command
• sg_read_block_limits(8) send SCSI READ BLOCK LIMITS command
• sg_read_buffer(8) send SCSI READ BUFFER command
• sg_read_long(8) send a SCSI READ LONG command
• sg_read(8) read multiple blocks of data, optionally with SCSI READ commands
• sg_readcap(8) send SCSI READ CAPACITY command
• sg_reassign(8) send SCSI REASSIGN BLOCKS command
• sg_referrals(8) send SCSI REPORT REFERRALS command
• sg_rep_pip(8) send SCSI REPORT PROVISIONING INITIALIZATION PATTERN command
• sg_rep_zones(8) send SCSI REPORT ZONES command
• sg_requests(8) send one or more SCSI REQUEST SENSE commands
• sg_reset_wp(8) send SCSI RESET WRITE POINTER command
• sg_reset(8) sends SCSI device, target, bus or host reset; or checks reset
• sg_rmsn(8) send SCSI READ MEDIA SERIAL NUMBER command
• sg_rtpg(8) send SCSI REPORT TARGET PORT GROUPS command
• sg_safte(8) access SCSI Accessed Fault-Tolerant Enclosure (SAF-TE) device
• sg_sanitize(8) remove all user data from disk with SCSI SANITIZE command
• sg_sat_identify(8) send ATA IDENTIFY DEVICE command via SCSI to ATA
• sg_sat_phy_event(8) use ATA READ LOG EXT via a SAT pass-through to fetch
• sg_sat_read_gplog(8) use ATA READ LOG EXT command via a SCSI to ATA
• sg_sat_set_features(8) use ATA SET FEATURES command via a SCSI to ATA
• sg_scan(8) scans sg devices (or SCSI/ATAPI/ATA devices) and prints
• sg_seek(8) send SCSI SEEK, PRE-FETCH(10) or PRE-FETCH(16) command
• sg_senddiag(8) performs a SCSI SEND DIAGNOSTIC command
• sg_ses_microcode(8) send microcode to a SCSI enclosure
• sg_ses(8) access a SCSI Enclosure Services (SES) device
• sg_start(8) send SCSI START STOP UNIT command: start, stop, load or eject
• sg_stpg(8) send SCSI SET TARGET PORT GROUPS command
• sg_stream_ctl(8) send SCSI STREAM CONTROL or GET STREAM STATUS command
• sg_sync(8) send SCSI SYNCHRONIZE CACHE command
• sg_test_rwbuf(8) test a SCSI host adapter by issuing dummy writes
• sg_timestamp(8) report or set timestamp on SCSI device
• sg_turs(8) send one or more SCSI TEST UNIT READY commands
• sg_unmap(8) send SCSI UNMAP command (known as 'trim' in ATA specs)
• sg_verify(8) invoke SCSI VERIFY command(s) on a block device
• sg_vpd(8) fetch SCSI VPD page and/or decode its response
• sg_wr_mode(8) write (modify) SCSI mode page
• sg_write_buffer(8) send SCSI WRITE BUFFER commands
• sg_write_long(8) send SCSI WRITE LONG command
• sg_write_same(8) send SCSI WRITE SAME command
• sg_write_verify(8) send the SCSI WRITE AND VERIFY command
• sg_write_x(8) SCSI WRITE normal/ATOMIC/SAME/SCATTERED/STREAM, ORWRITE commands
• sg_xcopy(8) copy data to and from files and devices using SCSI EXTENDED
• sg_zone(8) send a SCSI ZONE modifying command
• sg3_utils(8) a package of utilities for sending SCSI commands
• sginfo(8) access mode page information for a SCSI (or ATAPI) device
• sgm_dd(8) copy data to and from files and devices, especially SCSI
• sgp_dd(8) copy data to and from files and devices, especially SCSI